Mounting a scope on the PS 90 for +-$25.00 - FN FiveseveN Forum

Mounting a scope on the PS 90 for +-$25.00 - FN FiveseveN Forum

Posted by schmidtbender:

I don't think much of the as issued sight. In fact it is clearer with my glasses off than on. I got to thinking about putting a real scope on it and like a true shadetree gunsmith, I "figgered it out".
You need:
1. A 1"x1"x1" piece of square steel "tube" about 1.3" long
2. Two metric allen set screws that fit the existing holes in the side of the sight housing. Take along one of the sight mounting screws as it's the same thread. (I bought four and used the other two to plug the other two holes in the wings).
4. A piece of tip off mount adapter rail from Brownells (see picture).
5. A scope with a tip off mount. You can get the rings in 3/4", 7/8" and 1" for sure on ebay or from Brownells. This is NOT a Weaver crosslock ring set, it is the kind designed for 22s with grooved receivers.
6. Drills, taps and a belt sander

one: remove the existing sight and put the front screw back in (so you don't lose it).
two: Measure the distance between the sight guard ears.(See pics) It was a RCH less than 1" on mine, hence the belt sander.
three: Get it to where it is a press and tap tap fit between the ears.
three: Level it with the flat where the rear OEM sight screw hole is.
four: Drill a 1/8" hole from each side thru the existing tapped hole in the sight wings. Do not drill thru the steel tube, it's just to locate the set screw.
five: Put in the two allen set screws and tighten a bit. This is not a 416 Rigby so be gentle.
six: Cut the Brownell rail to the length you want, drill & countersink a hole for the original rear sight mounting screw in the original hole.
seven: Install the rail with the rear screw and center it on the 1" tube piece. I used a caliper to measure the gap between the rail and the sides of the wings.
eight: Tighten down the rear screw making sure the rail does not move.
nine: Drill a countersink in the rail for whatever screw you use to secure it to the 1" tube. I used an 8-40 scope mount torx. Drill thru the rail with a clearance drill enough to spot the tube.
ten: Remove the rail and D&T the tube.
eleven: cleanup and degrease, mount the rail with blue locktite.
twelve. mount the scope.

My rig has a Leupold Alaskan 6X which is a 7/8" tube scope.
The cheek weld is much better that the OEM sight and I'm just a normal guy that can pick up almost any off the shelf rig and it fits.

To the range tomorrow. I may need to shim the front or rear base a bit for elevation but at least I'll be able to see that target.

3DM3 free video tutorials for digital artists, Largest world Challenges, FREE 3D MODELS, Award Gallery

3DM3 free video tutorials for digital artists, Largest world Challenges, FREE 3D MODELS, Award Gallery

3D Computer Models

Question on Tracer Round OAL - FN FiveseveN Forum

Question on Tracer Round OAL - FN FiveseveN Forum: "Keep it closer to 1.575-1.580. The ogive on military bullets vary dramatically and with some, on a longer OAL, may contact the lands/grooves spiking pressure. Also, the old white capped tracers are very unreliable. Only about 40% will light. If you can get the copper base tracers, you will experience 100% function. If you can't find any, drop me a PM or email and I'll get you some from my suppliers (at my cost). -Ryan P.S. I much prefer TrueBlue over HS6. It meters better and has a more even pressure curve. -RH"

FN Forum.NET :: View topic - FNH Q&A - November 30, 2007 - (ANSWERED)

FN Forum.NET :: View topic - FNH Q&A - November 30, 2007 - (ANSWERED)

1. When will we get more variations of factory 5.7x28mm ammo (besides 195 and 197)? There will be a new round called SS198 but it will be a LE restricted round. The 195 and 197 go forward for now.

2. Will official (CIP, SAAMI, FN internal) cartridge dimensions and other specifications eventually be included in the FNH USA website content for the 5.7x28mm? Not at this time.

3. There have been a handful of reports of PS90 barrels supposedly damaged from the higher pressures of the 195 round. Did extending the barrel on the PS90 to 16 inches have any unanticipated consequences over the original P90 design? Not true. If that was true the shorter P-90 barrel would have problems. I have seen P-90 barrels with 35,000+ rounds through them. The SS195 is not full pressure.

4. The PS90 manual states that the moving parts group should be oiled at the guide rods, ejector, extractor and "holes of the breech block". Which holes are they referring to? The side holes are the right hole that goes to the guide rod and the other side which houses the cyclical reducer or tungsten weight.

5. The PS90 Owners Manual states that the PS90 has an internal safety sear to prevent accidental firing if the gun is dropped. Since the this forward safety sear has been removed from the hammer group, has FNH done extensive tests to ensure there is no chance of an out of battery detonation?It is a gravity activated sear which activates when the gun is dropped on the muzzle. I am sure the fire control was tested and qualified before production started as on all FNH firearms.

6. Has the FNP 45 release date been pushed back? We should see .45's any time. There was a slight hitch in getting the extractors done.

7. Will the USG FNPs be available in both 9mm and .40 S&W? And will they be available with night sights? Both are available now. No plans for night sight versions.

8. Photos of the FNP45 show a lanyard loop. Will this be on the production pistol, and will it end up on the 9mm's and 40's as well? It will only be on the USG version. The loop will exist on all but only the USG will come with a split ring.

9. When is the FNP-357 Sig going to be available for purchase? Will they be released in dark earth color? 1st quarter 2008. They will not be available in dark earth at this time.

10. Will the FNP 357 be available in DA/SA with a decocker only?Yes, only DA/SA at this time.

Thanks for the questions!

Ken Flood
National Sales Manager
FNH-USA

WTS FN Five-seveN Tactical Model - FN FiveseveN Forum

WTS FN Five-seveN Tactical Model - FN FiveseveN Forum: "This is an original FN Tactical model with a notch cut out for a light or light/laser combo. Comes with everything that came from FN (2 non mag safety 20 round mags and owners manual leaflet). $1850 shipped obo."

FN Forum.NET :: View topic - WTS FN Five-seveN Tactical Model

FN Forum.NET :: View topic - WTS FN Five-seveN Tactical Model: "This is an original FN Tactical model with a notch cut out for a light or light/laser combo. Comes with everything that came from FN (2 non mag safety 20 round mags and owners manual leaflet). $1850 shipped obo. "

Packing Foam, Foam Packaging, Packaging, Packaging Material

Packing Foam, Foam Packaging, Packaging, Packaging Material: "Protect your shipments and ensure your packages arrive safely. We stock many types of foam to pad packages for shipping. Each foam can be cut into custom shapes, to your custom dimensions. We also sell convoluted (egg-crate style) packing foam sheets. All sales of packing foam are final; no warranty coverage is offered. "

Good gun case foam - FN FiveseveN Forum

Good gun case foam - FN FiveseveN Forum: "Just for the info of anyone interested, I found a good place to get foam for cases: http://www.foamorder.com/packing.html I got both the CD100 and 3002 foam and they are great and the prices are good. Easy to cut, and they ship it in exactly the dimensions that you specify. Regards, Wolly"

:: View topic - WTS - Custom Suppressor Pouch ***NEW COLORS AVAILABLE***

:: View topic - WTS - Custom Suppressor Pouch ***NEW COLORS AVAILABLE***

SUPPRESSOR POUCH
Designed and custom built to order, specifically to the dimensions of YOUR suppressor! Each pouch is handcrafted using MIL spec 1000 denier Cordura®, all seams bound and double stitched. Side release buckle closure. Every Battlecloth Suppressor Pouch has an integrated forms pocket for your paperwork, so you can keep a clean copy of your tax form WITH the can at all times. Not just well made but over built right here in the USA. Available in black, OD and Coyote Tan or Brown and Cre Mutlicam to match your existing military gear. ALICE clip, belt loop or MOLLE compatoble attachment.

Prices start at just $26.95 - Certified funds (PMO, bank check or cash) ship upon receipt, personal checks now clear in ONE business day!

PLEASE EMAIL WITH THE LENGTH, WIDTH AND WEIGHT OF YOUR SUPPRESSOR FOR AN EXACT QUOTE TO: Battlecloth@comcast.net

*** WARNING ***Suppressor manufacturers can and do change the dimensions of production cans and specs posted on the Internet are not to be trusted. Please take a minute and actually measure you suppressor. One-quarter inch in error can easily mean the difference between a perfect fit and not fitting at all.

Mail orders to:
Battlecloth
P.O. Box 225
Newtown, PA 18940

KBP. Hunting Arms

KBP. Hunting Arms

Quad-barrel (!) shotguns

Dixie Consolidated - LP4 Gallery

Dixie Consolidated - LP4 Gallery

More Bullpup 10/22s

FN Forum.NET :: View topic - WTS - NEW PS90 Receiver - Complete

FN Forum.NET :: View topic - WTS - NEW PS90 Receiver - Complete: "Clearing out my excess parts.... 5 months NEW - SN 47xxx - Unfired - USG PS90 Receiver, comes complete as pictured w/ springs and cocking handle (bottom pic). See pictures for full details. $450 Shipped OBO. All this needs to fit your PS90 is a Short or Full Length Barrel. Ships to FFL, can be shipped from FFL if needed. Great for an SBR Project!"

Tinkering with the Ruger 96 - Jesse's Hunting & Outdoors (JHO)

Tinkering with the Ruger 96 - Jesse's Hunting & Outdoors (JHO): "Tinkering with the Ruger 96 Andy Moe - JHO ProStaff - Montana July 28, 2006 I'm a fan of the Ruger 96 lever actions. A lot of people don’t even know what they are but I like them. They appeal to my taste for the eccentric. Looking like a mongrel cross between a Ruger 10/22, a Savage Model 99, and the old Winchester Model 88 centerfire, this rifle is not just another pretty face. "

[article continues]

Thanks to Herstal, MO, and all the rest. - FN FiveseveN Forum

Thanks to Herstal, MO, and all the rest. - FN FiveseveN Forum

I would like to Thank everyone that has contributed to the Reloading section. Yesterday I chronographed my first reloads.

Thanks to:

Hestal for a great shell plate for my dillon. My only problem was the powder measure. I have an older 550 and the original powder measur would not fully actuate with the small 5.7x28 case. Luckily I had purchased a second powder measure to have one for pistol and one for rifle. The new one worked just fine.

MO for sharing his wealth of experience with reloading.

Charlie Foster for sharing his reloading data.

I was looking for a sub sonic load. I loaded a Win 55gr fmj, WSR primer, 3.0 grs HS6, once fired brass, COL 1.58.
Avg - 1036.8, HI - 1072.2, Low - 992.6, SD - 19.5

I also tried some 40gr Vmax, with 7.4 grs of AA#7.
Avg - 2227.8, HI - 2266.2, Low - 2195.9, SD - 19.2

I had accidently picked up the moly coated Vmax bullets. Would that explain why the velocity at 7.4 grs exceeded the powder mfg specs for a 40 gr bullet, that had a max of 7.7 grs 2044 fps?

Sidearmor: Kydex® Holsters, Shotgun Equipment, Rifle Equipment and firearms accessories

Sidearmor: Kydex® Holsters, Shotgun Equipment, Rifle Equipment and firearms accessories: "Using the same CAD design tools and CNC machining technology we use for our weapon mounts, Sidearmor has created the worlds' premier holsters. Each holster is formed from Kydex® 100 sheet, which features a high impact resistance and UV stable for the most demanding applications. It is also impervious to chemicals and will maintain its performance under harsh circumstances. Sidearmor holsters are formed using custom CNC cut tooling. Each model holster has it's own mold and it's own custom features. All our holsters feature a unique retention system we call the Isometric Tensioner. This ingenious device uses a combination of spring-load and an o-ring to provide opposing force and two aluminum pieces to spread the load out for a silky smooth draw and unparalleled adjustment and retention capabilities. The spring will not take a set like rubber bushings and the CNC construction and Military compliant (Mil-A-8625) Type III hard-anodized finish of the aluminum components will not wear out or deteriorate. Our Modular Outside The Waistband (OWB) holsters feature an innovative attachment system that can be custom tailored to your needs. A replaceable attachment system means varying options for varying circumstances. The detachable chassis system allows 60° of adjustment muzzle forward or muzzle rearward. It can be worn strong side or cross draw and with optional attachments, can be mounted to any surface. "

Sidearmor: Kydex® Holsters, Shotgun Equipment, Rifle Equipment and firearms accessories

Sidearmor: Kydex® Holsters, Shotgun Equipment, Rifle Equipment and firearms accessories: "sing the same CAD design tools and CNC machining technology we use for our weapon mounts, Sidearmor has created the worlds' premier holsters. Each holster is formed from durable Kydex® 100 sheet, which features a high impact resistance and is UV stable for the most demanding applications. It is also impervious to chemicals and will maintain its performance under harsh circumstances. Sidearmor holsters are formed using custom CNC cut tooling. Each model holster has it's own mold and it's own custom features. All our holsters feature a unique retention system we call the Isometric Tensioner. This ingenious device uses a combination of spring-load and an o-ring to provide opposing force and two aluminum pieces to spread the load out for a silky smooth draw and unparalleled adjustment and retention capabilities. The spring will not take a set like rubber bushings and the CNC construction and Military compliant (Mil-A-8625) Type III hard-anodized finish of the aluminum components will not wear out or deteriorate. Our Modular Outside The Waistband (OWB) holsters feature an innovative attachment system that can be custom tailored to your needs. A replaceable attachment system means varying options for varying circumstances. The belt slide system allows 45° of adjustment muzzle forward or muzzle rearward. It can be worn small-of-the back, strong side or cross draw. "

Help!! - FN FiveseveN Forum - Slide Cover Replacement

Help!! - FN FiveseveN Forum:

Here you go.

1. Remove magazine and unload weapon.
2. Remove magazine and unload weapon again in case you skipped step one.
3. Remove the slide.
4. Remove the barrel.
5. Set the slide down on its right side, so the FN stamp is facing you.
6. With a punch and hammer/mallet punch the Slide Cover pin from left to right
7. Remove the pin--note the knurled end is on the right side when you replace it.
8. Remove the slide cover starting from the rear NOT MUZZLE, you may need to
pry slightly to get it started.
9. Remove the cross pin.
10. Remove the firing pin and spring.
11. Once the cover is off remove the loaded chamber indicator and spring so you
don't lose it.
12. TAKE NOTICE OF THE SPRING THAT IS UNDER THE REAR SIGHT
OF YOUR PISTOL YOU MUST NOT LOSE THIS SPRING, Your pistol
will not function without it!!! This is held in place by the rear sight base plate and will fly off when the rear sight is removed. When you remove the rear sight cover
it with a cloth or something that will catch the spring. DO NOT LOSE IT.
13. Remove front and rear sights with a punch and mallet
14. Install the firing pin w/spring and cross pin.
15. Lay the slide upright and replace the small spring into the hole and
replace the chamber indicator and spring.
16. Place the new slide cover on muzzle first. Ensure that the tiny rear spring is in
place before you press it on completely.
17. Replace the slide cover pin right to left
18. Replace barrel, slide, and magazine.

And there you have it.

WTS: 15mm Crows Foot / 19mm Wrench for PS90 SBR Build - FN FiveseveN Forum

WTS: 15mm Crows Foot / 19mm Wrench for PS90 SBR Build - FN FiveseveN Forum: "I am making up a few more SBR wrench sets and have the following items available for sale. “Slimmed” Down 15mm Crows Foot to fit the slot on the chamber end of a CMMG and FN barrel. It has a 3/8 inch square for torque wrench drive. $42 shipped. 'Skinny' 19mm Wrench to fit the slot on a CMMG factory style flash hider. $28 shipped. If you would like both a 15mm crows foot and 19mm wrench, the 'package deal' price is $65 shipped. All NFA rules apply. Thanks for the use of the boards, Hoover in Pittsburgh, Pa hoover144@comcast.net"

FN Forum.NET :: View topic - Scope mount and front sight removal

FN Forum.NET :: View topic - Scope mount and front sight removal: "Ive modified an Aimtech rail mount # APM-1R to fit the Five-seven, which requires cutting and removing metal to allow for clearance in several locations, however the front sight is too low for the slide to work. Can anyone tell me if and how the front sight can be removed. This mount will allow for standard scope mounting, thanks, Flagman"

Precision Spring Manufacturer - Century Spring Corp.

Precision Spring Manufacturer - Century Spring Corp.

Lots of springs, including custom springs.

Gemtech's SFN-57 Test Spin [Archive] - FN FiveseveN Forum

Gemtech's SFN-57 Test Spin [Archive] - FN FiveseveN Forum: "I recently had the opportunity to hook up with Doc Dater and Kelly from Gemtech at a small MG Match and they happended to have the SFN-57 attached to a Tactical 5.7 Pistol. They said I could take it for a spin but they didn't have any ammo with them...... Lucky me. I'm still waiting for my Jarvis Barrel to be shipped.... sigh. I loaded up a 30 rounder with some S-190, S-192, S-195, S-196 and S-197 ammo to feel and hear if there were any notable difference in ammo with the suppressor. All of the rounds did have a noticible sonic crack but you could really tell the difference with the can and without..... I couldn't tell any difference in the crack between any of the rounds that I fired. The overall length of the suppressor was 5.8' The diameter was 1.25 inches and didn't interfere or block the Tactical sights. The weight was only 5.2 ounces and didn't make the pistol front end heavy. The suppressors have a M10x1 Thread. I definately need to get my hands on some S-193 Subsonic ammo and will be ordering one of these cans as soon as my barrel is shipped. Agent"

Kneseks Pictures (SFN-57)

Kneseks Pictures

SFN-57 [GEM-SFN-57] - $575.00 : Talon Arms!, Your on-line Tactical Tool Box

SFN-57 [GEM-SFN-57] - $575.00 : Talon Arms!, Your on-line Tactical Tool Box: "SFN-57 5.7x28 mm for FN 5.7 Pistols threaded M10x1"

AAC FiveSeven, 5.72mm Supressor - Centerfire Pistols by Big Sky Guns LLC

AAC FiveSeven, 5.72mm Supressor - Centerfire Pistols by Big Sky Guns LLC: "SILENCER For the FN Five-seveN 5.7mm pistol. Designed to be compact, lightweight, and durable, the FIVESEVEN silencer is designed for extreme duty use. The simple thread mounting system provides quick and easy attachment. Compact by design, the FIVESEVEN does not hinder sight recognition or CQC maneuverability. Durability is achieved by CNC automated fusion welding every stainless steel component used in its construction - making full-time suppression a reality. The elimination of approximately 95% of the muzzle report nullifies the need for ear protection, preserves field communications, and masks the location of the shooter. Physical Specifications: Weight: 7 oz. Length: 6 in. Diameter: 1 in. Materials: 316SS Finish: SCARmorTM Dark Gray Attachment: Metric threading Performance Specifications: Sound Reduction: 28-35dB Velocity: equal to unsuppressed Accuracy: equal to unsuppressed "

Other Silencers

Other Silencers: "Gemtech SFN 57 Quantity: US $ 530.00 Gemtech SFN-57 5.7 x 28mm Suppressor for the FN 5.7 Pistol, Threaded for the M10x1 Threaded Barrel (See Below), New. 5.8 Inches Long, 1.25 Inches in Diameter, 5.2 Ounces."

ColtCCO » I am a Splinter Cell.

ColtCCO » I am a Splinter Cell.: "Ok, I knew a Gemtech SFN-57 can weighs nothing. The FiveseveN weighs nothing, either. Just today I found out that, when both items are assembled together , they still weigh only slightly more than nothing, and even then, not by a lot. It’s just so handy. They already have about the recoil of a .22lr pistol, and the suppressor is only going to help attenuate that further. This setup belongs to a lucky customer of mine, and when we threaded the can on for the first time, I just couldn’t help but grab my then-working camera and snap a few shots. I wish I’d remembered to grab a scale too, but the whole package weighs under 2lbs, loaded with 21 rds. Now I really want to go play Splinter Cell - oh, wait, no, I can’t. My Xbox 360 is en route to Tejas for repair. That’s a post for another time, when I bitch about not be able to bypass any of the English script the tech support guy in India read to me about rebooting. Rrgh. Between my busted camera, busted Xbox, and busted PC case fan, I’m not gonna be too surprised if I mosey downstairs tomorrow morning and find that my microwave has spontaneously dissasembled on my countertop. ColtCCO"

Gemtech Suppressors & Silencers Sales Class 3 Weapons

Gemtech Suppressors & Silencers Sales Class 3 Weapons: "Gemtech SFN-57 (5.7x28mm, threaded M10x1 for FN57 Pistol)$575."

Gemtech SFN-57 7.7x28 - Centerfire Pistol by Big Sky Guns LLC

Gemtech SFN-57 7.7x28 - Centerfire Pistol by Big Sky Guns LLC: "GEMTECHSFN57 Gemtech SFN-57 7.7x28 Accepting Orders Price: $ 575.00 / Each"

GunsAmerica - GEMTECH SFN-57 (5.7x28mm) - Class 3 > Class 3 Suppressors

GunsAmerica - GEMTECH SFN-57 (5.7x28mm) - Class 3 > Class 3 Suppressors: "GEMTECH SFN-57 (5.7x28mm) GA LISTING NUMBER976785067 SELLER STOCK # CATEGORYClass 3 Suppressors CONDITION. Price: $529.00 Ask Seller A Question This is a brand new GEMTECH SFN-57 suppressor for the 5.7x28mm round. All NFA rules apply. Please add $10.00 for shipping & handling. "

Gemtech Silencers at Impact Guns Home

Gemtech Silencers at Impact Guns Home: "Gemtech SFN-57 Suppressor $499.99 Item #: GEM-SFN-57 [Add to Wishlist] [Add to Cart] Designed specifically for the FN 5.7 pistols."

Coal Creek Armory: SHHH! Quiet. More New Gemtech Silencers Are IN!

Coal Creek Armory: SHHH! Quiet. More New Gemtech Silencers Are IN!: "The Gemtech SFN-57 and a Jarvis threaded barrel is the perfect compliment to the FN FivenSeveN Pistol - the only thing better than this high velocity, high capacity and low recoil pistol, is a much quieter one. Super light and handy, Factory sights clear the silencer body with no trouble, and the fit is drop-in, no permenant modification requiet to hush the 5.7x28 screamer to a 'pop'. Shooters who want a practical pest control pistol, and fans of Splinter Cell alike will apreciate the SFN-57 on their FiveSeveN. The ultimate accessory for your FN Pistol. "

AmmoGuide Interactive

AmmoGuide Interactive

AmmoGuide.com User Agreement

The following describes the terms on which this Web site provides you access to our services. We reserve the right to supplement, revise, or update these terms at any time without notice to you other than by posting to this Web site. Continued use of this site following such notice (other than to discontinue your membership) shall be deemed to indicate your acceptance of said updates, revisions and additional terms and conditions.

Eligibility for Membership. Our services are available only to individuals who can form legally binding contracts under applicable law. Without limiting the foregoing, our services are not available to minors. If you do not qualify, please do not use our services.

1. Listing Reloading Data
When listing reloading data, ensure that the data listed does not infringe upon the copyright, trademark or other rights of third parties. By listing reloading data on this site you represent to us that your data does not infringe on the intellectual property of any third party and that you have a legal right to present the data you list.

Your description of the data must be truthful and accurate.

The sharing of your data on this site: (a) shall not be fraudulent or involve counterfeit or stolen data; (b) shall not infringe any third party's copyright, patent, trademark, trade secret or other proprietary rights or rights of publicity or privacy; (c) shall not violate any law, statute, ordinance or regulation (including without limitation those governing export control, consumer protection, unfair competition, anti-discrimination or false advertising); (d) shall not be defamatory, trade libelous, unlawfully threatening or unlawfully harassing; (e) shall not be obscene or contain child pornography; and (f) shall not contain any viruses, Trojan horses, worms, time bombs, cancelbots or other computer programming routines that are intended to damage, detrimentally interfere with, surreptitiously intercept or expropriate any system, data or personal information.

You may not post on our site any: (a) data that, by paying to us the subscription fee, could cause us to violate any applicable law, statute, ordinance or regulation, or (b) item for sale, including bulk email lists, illegal weapons, instructions/kits/plans/parts designed to illegally convert firearms to full-auto fire, instructions/kits/plans/parts designed to illegally build silencers, or instructions on how to build bombs or explosives.

In the event of a conflict the rules of the website as specified by this document supercede any other the terms stated. A lister may not alter the rules of the website by the language of his listing.


1. Listing Content / Multiple Listings. Data listings must specify components and performance to a minimum of bullet weight, powder type and charge and resultant velocity. Any listing deemed to be advertising will be removed. We reserve the right to edit or remove listings as deemed necessary. We reserve the right to remove any listing deemed inappropriate or in violation of the letter or spirit of our rules.

2. Fraud Prevention / Dispute Resolution. Complaints of fraud or wrongdoing are extremely rare at AmmoGuide.com. We provide a forum where load posters and users can publicly post their experiences with each other. AmmoGuide.com encourages it's members to self-police where possible. In matters where fraud is suspected, against the website, it's data store or another subscriber, AmmoGuide.com reserves the right to arbitrarily terminate and refuse service to any party.

3. System Abuse. This site reserves the right to refuse service to anyone. We will exercise this right with "problem" subscribers who repeatedly create dissention in the forum, post questionable load data or recommend or exhibit dangerous loading practices.
Without limiting any other remedies, this site may terminate your account if you are found (by conviction, settlement, insurance or escrow investigation, or otherwise) to have engaged in fraudulent activity in connection with our site.

You agree to be liable for and to pay for any costs incurred by this site for your misuse of the site or for your violation of any of the site's rules, including the cost of our time spent in resolving deliberate rules violations.


4. Technical Difficulties. This site is not responsible for downtime due to technical difficulties.

5. User-Generated Content. This site is not responsible for the content of user-generated content including data listings, messages on our message forums, personal messages, pictures, etc.
You are solely responsible for any information you post or use on this site, and not permitted further distribution and/or publication of this information. If you post information that is slanderous, violates any international, federal, state, or local law, or violates the intellectual property of another party you will be solely liable for the consequences. We may take any action with respect to such information we deem necessary or appropriate in our sole discretion if we believe it may create liability for us or may cause us to lose (in whole or in part) the services of our ISPs or other suppliers.

Complaints of copyright violations or infringement of any other type of intellectual property are covered in this document under the section labeled Intellectual Property.


6. Illegal Acts. By registering as a member of and using this site you agree to not violate any applicable local, state, federal and/or international laws.

7. Registration. Members agree to provide true and accurate information about him/herself in the registration form/account creation process.

8. Payments And Fees. Any and all payments made to this site are non-refundable.
Returned checks are subject to a $25.00 returned check fee. Writing bad checks is a criminal offense; don't do it because we will prosecute.

By placing a credit card on file with us you expressly authorize us to charge your card for any fees you accrue as a result of using (or misusing) this site. You authorize us to consolidate balances from any duplicate accounts you may have created on our site and bill them to your credit card. You may revoke your authorization by sending a written request to AmmoGuide.com, PO Box 21807, El Sobrante CA, 94820. We reserve the right to continue to bill your card for any services rendered prior to receipt of your written request, or for any fees accrued for any action taken prior to the receipt of your written request.

By using a credit card to pay us you agree to unconditionally waive any and all 'chargeback' rights. If you have a question about a charge on your credit card you agree to contact us as described on our Contact Us page. If you deliberately or inadvertently issue a 'chargeback' to your credit card, your account will be terminated and you agree to pay a $50 processing and collection fee to cover our costs for processing the chargeback for each and every chargeback initiated. Failure to pay these fees will result in your account being turned over to a collection agency and we will pursue civil and criminal legal actions to the fullest extent of the law.

Past due accounts will be terminated. Past due balances will be subject to a finance charge of 1.5% per month or the highest amount permitted by applicable law; whichever is lower. If your account is past due you agree to pay any and all collection costs including but not limited to court costs, attorney's fees, collection agency fees, and administrative costs.

Unless otherwise stated, all fees are quoted in U.S. Dollars. You are responsible for paying all applicable taxes and for all hardware, software, service and other costs you incur to access our servers. We may in our sole discretion add, delete or change some or all of our services at any time.


9. Messaging Systems / Spam. Our forum and personal messaging systems exists solely to allow contact between subscribers for the purpose of furthering ammun ition-related interests and knowledge. Use of the messaging systems for any other purpose is prohibited.
Users agree to refrain from "spamming" (sending unsolicited commercial email to other users). Users may not send spam through this site or through other mail servers for any purpose, including promoting this site to earn affiliate program rewards. Spamming will be reported to the applicable ISP(s) for further punitive action and may result in criminal or civil penalties under various laws.

Abuse of our messaging systems and/or sending spam is a serious offense and will result in closure of your account here.


10. Maintenance / System Downtime. We reserve the right to initiate system downtime for maintenance purposes at anytime.

11. Termination. This site may, at its sole discretion, terminate Service should Member's conduct fail to conform to this User Agreement or other rules of this site. Abusiveness or use of profanity directed toward this site, its personnel or other subscribers will result in immediate termination of the Member's account here.

12. Intellectual Property. You agree that all information on the AmmoGuide.com website is the intellectual property of the AmmoGuide.com owners. You further agree to refrain from posting or transmitting any materials that infringe any third party's intellectual property, including copyright, patent, trademark, trade secret or other proprietary rights or interests. If you believe that materials posted on this site violate your copyright you can contact the site's designated agent as per the Digital Millennium Copyright Act and file a claim of infringement. It is further agreed that access to information on this website is granted by subscription only, and under no circumstance does it include the right to download or otherwise create a local or cached copy of this database for private or commercial use.

Terms of Use and Service
ACKNOWLEDGMENT AND ACCEPTANCE OF TERMS OF SERVICE
This Site ("Service"), owned and operated by this Site Owner ("AmmoGuide.com"), is provided to you under the following Terms of Service and any operating rules or policies that may be published by this Site. The Terms of Service comprise the entire agreement between Member and this Site and supersede all prior agreements between the parties, regarding the subject matter contained herein. By participating in the registration process, you are indicating your agreement to be bound by all of these Terms of Service.

DESCRIPTION OF SERVICE
This Site is providing Member with a subscription for a specific period of time to participate in various services, including access to a contemporary database of reloading data combined with communication facilities with other Members, for the Member's entertainment and edification in that area. In consideration for this Service, Member agrees to: (1) provide certain current, complete, and accurate information about Member as prompted to do so by the Service and (2) maintain and update this information as required to keep it current, complete and accurate. All information requested on original sign up shall be referred to as registration data ("Registration Data"). Furthermore, Member grants this Site the right to disclose to third parties certain Registration Data about Member and Service membership in the aggregate; however, such disclosures will exclude Member's name, mailing address, email address, account and phone number, unless: (1) Member expressly directs this Site, or any other person, Member may specifically designate to disclose such information through the Service as provided by the Service, or (2) this Site is required to disclose such information by any applicable law or legal process served on this Site.

If any information provided by Member is incomplete or inaccurate, this Site retains the right to terminate Member's membership and rights to use the Service.

MODIFICATIONS TO TERMS OF SERVICE
This Site reserves the right to modify these terms and conditions at any time without notice. Member's continued use of the Service constitutes an affirmative: (1) acknowledgment by Member of these Terms of Service and any modifications; and (2) agreement by Member to abide and be bound by these Terms of Service and modifications.

MODIFICATIONS TO SERVICE
This Site reserves the right to modify or discontinue the Service with or without notice to Member. This Site shall not be liable to Member or any third party should this Site exercise its right to modify or discontinue the Service.

SITE OBLIGATIONS
Member acknowledges and agrees that this Site does not endorse any of the information presented through the Service.

Member acknowledges and agrees that this Site is not responsible for any damages, nor for misrepresentations by Members. Member acknowledges and agrees that any dispute involving this Site shall be settled by arbitration in the state of California, USA pursuant to the Rules of the National Arbitration Forum.

MEMBER ACCOUNT, PASSWORD, AND SECURITY
As a member of the Service, you have received a user ID and a password. You are entirely responsible if you do not maintain the confidentiality of your user ID and password. Furthermore, you are entirely responsible for any and all activities, which occur under your user ID and password. Member agrees to immediately notify this Site of any unauthorized use of Member's user ID or any other breach of security known to Member.

DISCLAIMER OF WARRANTIES
MEMBER EXPRESSLY AGREES THAT USE OF THE SERVICE IS AT MEMBER'S SOLE RISK. THE SERVICE IS PROVIDED ON AN "AS" AND & "AS AVAILABLE" BASIS. THIS SITE EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
THIS SITE MAKES NO WARRANTY THAT THE SERVICE WILL MEET YOUR REQUIREMENTS, OR THAT THE SERVICE WILL BE UNINTERRUPTED, TIMELY, SECURE, OR ERROR FREE; NOR DOES THIS SITE MAKE ANY WARRANTY AS TO THE RESULTS THAT MAY BE OBTAINED FROM THE USE OF THE SERVICE OR AS TO THE ACCURACY OR RELIABILITY OF ANY INFORMATION OBTAINED THROUGH THE SERVICE OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. THIS SITE MAKES NO WARRANTY REGARDING ANY GOODS OR SERVICES PURCHASED OR OBTAINED THROUGH THE SERVICE OR ANY TRANSACTIONS ENTERED INTO THROUGH THE SERVICE. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY MEMBER FROM THIS SITE OR THROUGH THE SERVICE SHALL CREATE ANY WARRANTY NOT EXPRESSLY MADE HEREIN. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF CERTAIN WARRANTIES, SO SOME OF THE ABOVE EXCLUSIONS MAY NOT APPLY TO YOU.

LIMITATION OF LIABILITY
THIS SITE SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR THE INABILITY TO USE THE SERVICE, OR FOR COST OF PROCUREMENT OF SUBSTITUTE GOODS AND SERVICES, OR RESULTING FROM ANY GOODS OR SERVICES PURCHASED OR OBTAINED, OR MESSAGES RECEIVED OR TRANSACTIONS ENTERED INTO THROUGH THE SERVICE OR RESULTING FROM UNAUTHORIZED ACCESS TO, OR ALTERATION OF MEMBER'S TRANSMISSIONS OR DATA, INCLUDING BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, USE, DATA OR OTHER INTANGIBLE, EVEN IF THIS SITE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO SOME OF THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

NO RESALE OR COMMERCIAL USE OF THE SERVICE
Member's right to use the Service is personal to Member. Member agrees not to resell or make any commercial use of the Service, or the data accessed therein, without the express written consent of Mike Haas.

OTHER LIMITATIONS
This Site retains the right, at our sole discretion, to determine whether or not Member's conduct is consistent with the letter and spirit of these Terms of Service and User Agreement. This Site reserves the right to terminate service if a Member's conduct is found to be inconsistent with these Terms of Service and User Agreement.

MEMBER CONDUCT
Member is solely responsible for the contents of his or her transmissions through the Service. Member's use of the Service is subject to all applicable local, state, national and international laws and regulations. Member agrees: (1) to comply with US law regarding the transmission of technical data exported from the United States through the Service; (2) not to use the Service for illegal purposes; (3) not to interfere or disrupt networks connected to the Service; and (4) to comply with all regulations, policies and procedures of networks connected to the Service.

Member agrees not to transmit through the Service any unlawful, harassing, libelous, abusive, threatening, harmful, vulgar, obscene or otherwise objectionable material of any kind or nature. Member further agrees not to transmit any material that encourages conduct that could constitute a criminal offense, give rise to civil liability or otherwise violate any applicable local, state, national or international law or regulation. Attempts to gain unauthorized access to other computer systems are prohibited. This Site may, at its sole discretion, immediately terminate Service should Member's conduct fail to conform with these Terms of Service and User Agreement.

INDEMNIFICATION
Member agrees to indemnify and hold this Site, its parents, subsidiaries, affiliates, officers and employees, harmless from any claim or demand, including reasonable attorneys' fees, made by any third party due to or arising out of Member's use of the Service, the violation of these Terms of Service by Member, or the infringement by Member, or other user of the Service using Member's computer, of any intellectual property or other right of any person or entity.

TERMINATION
Should Member object to any of these Terms of Service or any subsequent modifications thereto or become dissatisfied with the Service in any way, Member's only recourse is to immediately: (1) discontinue use of the Service; (2) terminate Service membership; and (3) notify this Site of termination.

PARTICIPATION IN PROMOTIONS OF ADVERTISERS
Member may enter into correspondence with or participate in promotions of the Advertisers showing their products on the Service. Any such correspondence or promotions, including the delivery of and the payment for goods and services, and any other terms, conditions, warranties or representations associated with such correspondence or promotions, are solely between the corresponding Member and the Advertiser. This Site assumes no liability, obligation or responsibility for any part of any such correspondence or promotion.

LAWS
These Terms of Service shall be governed by and construed in accordance with the laws of the state of California. Member and this Site agree to submit to the exclusive jurisdiction of the courts of the state of California. If any provision(s) of these Terms of Service is held by a court of competent jurisdiction to be contrary to law, then such provision(s) shall be construed, as nearly as possible, to reflect the intentions of the parties with the other provisions remaining in full force and effect. This Site's failure to exercise or enforce any rights or provisions of these Terms of Service shall not constitute a waiver of such right or provision unless acknowledged and agreed to by this Site in writing. Member and this Site agree that any cause of action arising out of or related to this Service must commence within one (1) year after the cause of action arose; otherwise, such cause of action is permanently barred. The section titles in these Terms of Service are solely used for the convenience of the parties and have no legal or contractual significance

Welcome to the official FN HERSTAL website

Welcome to the official FN HERSTAL website



The P90® TACTICAL, 5.7 x 28 mm.

A tactical version
Features
Technical data

Click here for a larger view of the product


--------------------------------------------------------------------------------



A Tactical version

The new P90® Tactical has been provided with two side rails and an enlarged top MIL-STD 1913 Picatinny interface.

The side rails will take accessories such as tactical lights and external lasers. The top interface has been enlarged to accept the in-line assemblig of a light amplifier and a red dot sight for night vision. The sights can be positionned to give the correct eye relief and reassembled without loss of zero.

The top rail comes with a built-in emergency iron sight, should the external sights malfunction or get broken in action.

Available with or without integrated laser pointer (visible/IR), the P90® Tactical retains all the ergonomic features of the standard model and offers the same unmatched performances.


The built-in emergency iron sight
is adjustable in windage and elevation


--------------------------------------------------------------------------------



Features





--------------------------------------------------------------------------------


[Top of the page]

Technical data :

• Caliber 5.7 x 28 mm
• Weight w. empty mag 2.768 kg (6.10 lbs)
• Overall length 50 cm (19.68 in)
• Width 55 mm (2.16 in)
• Height 197 mm (7.75 in)
• Magazine capacity 50 rounds
• Firing modes Single shot, full auto
• Firing rate 900 rpm
• Effective range 200 m



--------------------------------------------------------------------------------
[Top of the page]






The Herstal Group
History
Mission Statement
Contact
Homepage
Machine guns
Assault rifles
5.7x28mm System
Handguns
Ammunition
.50 Cal M2HB-QCB
MAG
Minimi™ 7.62
Minimi™ 5.56
F2000
FNC
P90®
Five-seveN®
Ammunition
MK3S
BDA9/O
FNP9-M
Five-seveN®
Machine guns
Air Weapon Systems
Land Weapon Systems
Sea Weapon Systems
.50Cal M3M
7.62 MAG58M
Fully Integrated Systems
> Equipment capabilities
> Armament integration
Helicopter mounts
> .50Cal Mounts
> 7.62mm Mounts
Pods
> .50Cal HMP
> .50Cal & 2.75''Cal RMP
Rocket launchers
Rockets
Vehicle Mounts
>ARROWS
>.50 Cal
Boat Mounts
>.50 Cal MBP
>7.62mm LBP
Handguns
5.7x28mm System
Shotguns
Ammunition
Less Lethal
FNP9-M
MK3S
GP SFS
BDA9/O
Five-seveN®
P90®
P90® Tactical
Five-seveN®
Ammunition
Self Loading Police Shotgun
FN303 launcher
FN303 accessories
FAQs about ...
Operating mode
Projectiles
Maintenance
Training & tactics
Compressed air
Competition
What's new ?
Trade shows
Desktop
Job opportunities
Military Missions
Law Enforcement Missions
FN303 launcher
FN303 accessories
FAQs about ...
Operating mode
Projectiles
Maintenance
Training & tactics
Compressed air
Competition
FN303 launcher
FN303 accessories
FAQs about ...
Operating mode
Projectiles
Maintenance
Training & tactics
Compressed air
Competition
Transfer of Know-how
Turnkey Project
management
Maintenance
Ballistic products
Training
General
Partnership/Association
Maintenance types
Technical support

Welcome to FN Manufacturing, LLC

Welcome to FN Manufacturing, LLC

FN Manufacturing is an equal employment opportunity employer and we do not discriminate on the basis of race, color, religion, sex, national origin, age, veteran, disability, or any other similarly protected status.


FN is currently accepting applications for the jobs listed below


CNC Operator /
Plans and performs a variety of machine operations utilizing computerized numerical control machining centers to cut, shape, or form metal work-pieces to specifications.


Weapons Tester
Participate in the testing of manufactured weapons. This person will be responsible for targeting handguns and other firearms associated duties and must have extensive firearm knowledge.


Welder
Designs, fabricates and welds metal and sheet metal components to fabricate or repair products.


Tool & Gage Technician / 2nd Shift
Simple-complex tool and gage making projects. Able to fabricate from start to finish any gage / fixture using any piece of tool room equipment efficiently & trouble shoot or repair fixtures or gages


QA Technician
Working from blueprints, drawings, process documents, and using a wide variety of tools, gages, jigs, and measuring equipment, audits product at various stages of the manufacturing process.


Project Engineer I/ II
Engineer needed for new product development. Project management to include proposal generation, budgeting, scheduling and reporting. Product design to include product support, concept development, Pro/E modeling and drawing, engineering analysis,procurement and testing of prototypes. Education and/or Experience: B.S.M.E. degree and three (3) to five (5) years of product design experience, or M.S.M.E. and seven (7) years experience with at least two (2) years of product design and development. Pro/Engineer (3d Modeling) software competency or a sufficient equivalent. Working knowledge of GD&T and ASME Y14.5 Standards


Surface Finish Operator /
Interprets basic drawings, program sheets, instructions, and process sheets to determine work to be done for the treatment of production parts. Degreases parts and cleans them by hand or machine blasting to eliminate all oxides. Processes parts installed on racks in degreasing chromium baths, phosphating neutralization baths and oiling and/or rinse tank. If required, operates oven for hydrogen em-brittlement relief. Gage barrels for bore and rifling on air column gages. Maintains specified temperature of baths Sets up controls and regulates plating equipment to coat metal parts with protective chromium. May replace anodes and cathodes of chrome plating equipment. Check plating process using chemical tests and sensitive instruments, including micrometers, calipers and permascope.


Conventional Operator
Operate simple conventional machines; make adjustments, change tools, etc., as required. Perform change over as required.Develops, records, analyzes, and interprets SPC charts and data and initiates and/or takes corrective actions necessary to return process to control. Qualifies as required production for compliance to engineering and quality specifications. Qualifications: High School diploma or general degree (GED); or zero to one year related experience and/or training; or equivalent combination of education and experience. Basic Shop Math / Blueprint reading, must be able to calculate metric and standard measurements and interpret. SPC.


Design Engineer
Ability to design and implement mechanisms. Understanding of near net shape processes and implementation into weapon design. Solid understanding and application of GD&T, ASME Y14.5 standards. Pro-E proficiency required. Wildfire and PDM Link experience a plus Work in a teaming environment. Accustomed to supplier and customer interfacing. Understanding of production/product configuration managment regiments Knowledge of weapon design and usage a plus Some travel possible Education: BSME degree and 5 years experience minimum


Cell Operator / Week-end Shift
Decide which steps (inspect, deburr, and load parts) to take in order to maintain continuous parts production with minimal supervision. Runs two or more complex operations using CNC and conventional machines, operating and controlling multiple parts simultaneously. Responsible for tool changes as required. Adjusts offsets to make quality parts Responsible for regular maintenance duties on assigned machines (examples: maintaining coolant, coolant concentrate and hydraulic oil at correct levels)


Assembler / M240 / Weekend Shift
Interprets basic drawings, program sheets, instructions, and process sheets to determine work to be done. Performs a variety of milling, drilling, grinding, riveting and turning on conventional machines or related operations to close and interrelated tolerances. Reviews OCS / OS sheet and specifications to determine machining sequence, tooling requirements / changes and dimensions of finished workpiece. Able to perform simple sub-assemblies. Perform tool changes on simple operations such as drilling and reaming operations. (i.e. sanding belts and grinding wheels) Performs a variety of inspection and gaging operations to insure maintenance of quality standards and specifications (metric & inch) (i.e. Venier calipers, microhite, micrometers)


Final Operations (Weapons Cleaner/Packaging)
Disassemble, clean and inspect all individual parts of tested weapons and components for one or more product lines in accordance with appropriate OCS. Preserves weapons and components. Maintains sufficient amounts of cleaning materials.


Project & Business Specialist
Responsible for coordination and management of training, both initial and on-going for major software systems as well as software user process definition and best practices mplementation/standardization. Position interfaces with users to assure that software systems are used in the most effective manner. Also assists with user coordination/leadership of software system evaluations and software system upgrades as well as custom programming definition, user testing, training, etc. in conjunction with user, programming resources and MIS management. Must assure compliance with all Federal, State, and local regulations and laws including the Uniform Commercial Code (UCC), copyright laws, Federal acquisition regulations (FAR), and regulations as defined by specific contracts.


Production Supervisor
• Five - Seven years as a supervisor (20-35 employees) in a metal working environment. • Bachelors’ degree in business or two year technical degree in Engineering or Machine Tool. • Total exposure to a total quality environment and familiar with ISO 9000 standards.


Engineering Systems Administrator
• Responsible for installation, configuration and support for Pro/Engineer and Windchill applications • Advanced knowledge of Pro/Engineer Wildfire modeling concepts required • 3 years experience administering Pro/E and Windchill applications required • Working knowledge of C++, VB, PERL, SQL and java a plus • BS in engineering preferred


Contracts Specilist
• Reviews complex customer documents such as, solicitations, contractual terms & conditions, SOWs, NDAs, LOAs, and MOAs to identify potential business opportunities, risks and develop appropriate strategies. • Understands financial considerations such as ROS, cash flow, working capital, etc. as they apply to the contracting process. • Works assigned programs independently with a minimum of supervision. Educational/Experience Requirements: • B.A. or B.S. in contract, marketing, management and/or legal area • Advanced degree or CFCM desirable • Five (5) to Seven (7) years of USG contracts and proposal experience within a manufacturing environment. • Thorough working knowledge of FAR/DFAR and other applicable laws and regulations as they apply to the sale of FNM products and services.

FA556AR (M4FA) Suppressor - FA556AR available from SureFire

FA556AR (M4FA) Suppressor - FA556AR available from SureFire

The FA556AR has an over-the-barrel design similar to the Finnish "reflex" design. This might be a cool option for a non-SBR PS90 since it would only add four inches to the OAL.